Comments for Acinonyx Weblog

Comment on DWL-900AP+ rev.C Modified firmware by pinel

pinel — Tue, 07 Sep 2010 15:28:00 +0000

hi, hi used Acinonyx firmware 3.06.06 for dwl900ap+ rev c2

is wlan wifi is issue

my net wifi works for a sure period then to scompare, contretto to extinguish and to relight AP. with firmware it originates them this does not happen. how I can resolve the problem using your to firmware?

Comment on D-link DWL-900AP+ rev.C Hardware Overview by geekgirl

geekgirl — Tue, 07 Sep 2010 19:22:00 +0000

As to the missing UART, you can see in my previous link to the HRI mailarchive (on SF.net) that the OP has posted log from serial console. How? Looks like he found the pins for UART (RX & TX) on the Conexant chip itself, very hackish, but hey, it works for him(tm) lol.. pic here of his UART mod: http://pages.sbcglobal.net/greghol/routers/DI604/di604_top.jpg

I’m hoping to find schematic/pin-out for my Marvell 88E6218 (ARM9E) CPU (in the D-Link DI-604 Rev.E) to do the same

Comment on D-link DWL-900AP+ rev.C Hardware Overview by geekgirl

geekgirl — Tue, 07 Sep 2010 19:17:00 +0000

Forgot to add, mine is DI-604 Rev. E. The guys over HRI (on SF.net) have hacked the DI-604 Rev A/C a bit, but it has different PLD. It appears the PLD plays the HW watchdog if the magic condition is not met after power-up, consequently issuing a reset. See: http://sourceforge.net/mailarchive/forum.php?thread_name=1082850820.830.29.camel%40mcosta&forum_name=hri-devel and pics/schematic of the bypass http://pages.sbcglobal.net/greghol/routers/DI604/

Comment on D-link DWL-900AP+ rev.C Hardware Overview by geekgirl

geekgirl — Tue, 07 Sep 2010 19:01:00 +0000

The Altera EPM3032-A PLD is probably used for address
decoding. That may explain why it is connected to the tiny Texas Instruments AHC74 (hex inverter). See: http://www.electronics-related.com/usenet/basics/show/55934-1.php

I have both the Altera EPM3032-A & the AHC74 in my ancient DI-604.

Comment on DWL-900AP+ rev.C Modified firmware by Giovanni

Giovanni — Tue, 07 Sep 2010 19:12:00 +0000

Hi and tnks for your work !!!
I have a question: I have two DWL 900 AP+, rev. C. I have tried to put them working in bridge mode with your firmware but they don’t. I have used MAC-ADDR of Ethernet interface. Do u have any suggestions ?
Thanks in advance.

Comment on Exploring Ubiquiti Bullet2 by Vaako

Vaako — Tue, 07 Sep 2010 17:50:00 +0000

it’s 20dBm = 100 mW (mili Watts).

Here some info for the ones who like to now:

Processor Specs: Atheros AR2313 SOC, MIPS 4KC, 180MHz
Memory Information: 16MB SDRAM, 4MB Flash
Networking Interface: 10/100 BASE-TX (Cat. 5, RJ-45) Ethernet Interface
RF Connector: Integrated N-type male Jack
TX Power: 20dBm, +/-2dB
RX Sensitivity: -95dBm +/-2dB
Outdoor Range: Depends on Antenna
TCP/IP Throughput: 25Mbps+
Enclosure Size: 152 x 37 x 31 mm
Weight: 0.18Kgr
Enclosure Characteristics: Outdoor UV Stabalized Plastic
Mounting Kit: Pole Mounting Kit included
Max Power Consumption: 4 Watts
Power Supply: up to 24V
Power Method: Passive Power over Ethernet (pairs 4,5+; 7,8 return)
Operating Temperature: -20C to +70C (System PCB optimized for hi-temp)
Operating Humidity: 5 to 95% Condensing

Regards,
Vaako

Comment on Exploring Ubiquiti Bullet2 by Vaako

Vaako — Tue, 07 Sep 2010 17:45:00 +0000

Hi,

Who nows what the TX output is from the Bullet2 AP ???

Thanks,
Vaako

Comment on DWL-900AP+ rev.B Modified firmware by Vaako

Vaako — Tue, 07 Sep 2010 17:43:00 +0000

@ Fojtik: version v2.62 is available but has lot of issues, so v2.61 is the best choice here

Thanks Acinonyx for this MOD!!!

Comment on Exploring Ubiquiti Bullet2 by p4ndaz

p4ndaz — Tue, 07 Sep 2010 10:57:00 +0000

Hi, can you tell me what tool do you use to unscrew the N connector ? thanks

Comment on Exploring Ubiquiti Bullet2 by celio

celio — Tue, 07 Sep 2010 22:22:00 +0000

Ola amigo como poço arumar uns componentes ksz8721b
obrigado a todos